Author Archives: admin

2023 Nissan Leaf EV Brake Line Damage

Posted on by

Nissan has determined that certain 2023 model year Nissan Leaf EVs may have a damaged right hand brake tube that could result in a brake fluid leak.

Nissan first became aware of the potential problem in January 2023 when a Nissan technician noticed a 2023 Nissan Leaf EV being assembled with a damaged right hand brake tube assembly. Nissan collected the affected parts and began an investigation. The investigation included a parts audit of 975 brake assemblies which revealed twenty-five (25) damaged right hand brake tubes at the actuator connection bend. Nissan also conducted a yard audit of 395 vehicles and found five (5) with a scratched or damaged right hand brake tube. These parts were quarantined and the vehicles were put on a quality hold.

According to the defect report, an investigation with the supplier determined that the incorrect tooling was used to align the brake tube into the pipe bending jig. Because the brake tube was misaligned, the tooling clamped the pipe in the incorrect position and caused scratching, and in some cases deformation of the tube, at the actuator bend.

Nissan performed corrosion and stress tests on two (2) of the worst case condition parts to evaluate the effect of the damaged brake tube on brake performance over time. Nissan concluded that the brake performance could be degraded and could lead to extended stopping distances possibly without prior warning. Nissan decided to conduct a Voluntary Safety Recall to recall all potentially affected LEAF vehicles to inspect the right-hand brake tube and replace any damaged brake tube assemblies.

Owners receiving notices will be asked to return to their dealers to have the right-hand brake tube inspected for damage. If damage is found, the affected brake tube will be replaced. Nissan’s number for this recall is PC976 and the NHTSA campaign number is 23V-362.

Stall From Unsecured Fuse Inside High Voltage Battery

Posted on by

Addressing the Issue of Unsecured Fuses and Steps to Take if Your Vehicle is Affected

Jeep Wrangler Plug-In Hybrid Electric vehicles (PHEV) have gained popularity for their eco-friendly features and impressive performance. However, recent reports have surfaced regarding a potential safety concern that could affect certain 2022-2023 models. The FCA Technical Safety and Regulatory Compliance (TSRC) organization has identified an issue with an unsecured fuse inside the high voltage battery, which may result in an unexpected loss of drive power.

Discovery of the Issue:
In February 2023, the FCA TSRC organization received its first report of a fuse melting in the HV battery of a 2022 Jeep Wrangler PHEV, drawing immediate attention to the matter. A subsequent incident involving another 2022 Jeep Wrangler PHEV with the same problem prompted the initiation of a comprehensive investigation.

Root Cause and Potential Impact:
The investigation revealed that an incorrect fastener used during vehicle production could increase resistance and generate excess heat at the 200 amp fuse interface. The prolonged exposure to high temperatures could cause the fuse to fail, leading to a loss of motive power. Drivers experiencing this issue might notice a Malfunction Indicator Lamp (MIL) illuminated, changes in drivability, and/or noise originating from the HV battery pack assembly.

Suspect Period and Population:
The suspect period for this issue spans from January 10, 2022, when the incorrect fasteners were introduced, to September 20, 2022, when the use of incorrect fasteners ceased. The identification of the suspect population was determined through careful examination of vehicle and supplier manufacturing records.

Recall and Resolution:
To address this safety concern, Jeep has issued a recall, known as recall number 53A by Chrysler and NHTSA campaign number 23V-303. Owners of affected vehicles will receive notifications instructing them to visit their authorized dealerships. At the dealership, the battery fuse will be inspected, and if necessary, replaced to ensure proper functionality. Additionally, the battery assembly will undergo inspection for signs of charring or discoloration on the bus bars, and if required, will be replaced as part of the resolution process. It is crucial to respond promptly to recall notifications and schedule an appointment with your dealership.

Taking Action if You Suspect Your Vehicle is Affected:
If you believe your Jeep Wrangler PHEV falls within the suspect population or are experiencing any symptoms associated with this issue, it is essential to take the appropriate steps. Firstly, check if you have received a recall notification from Jeep. The notice will provide instructions on how to proceed and schedule an appointment with an authorized dealership. If you have not received a notification but suspect your vehicle may be affected, you can directly contact your local dealership to inquire about the recall and share your concerns.

Conclusion:
The discovery of an unsecured fuse issue affecting certain 2022-2023 Jeep Wrangler Plug-In Hybrid Electric vehicles is a matter of utmost importance. If you suspect that your vehicle is part of the affected population or are experiencing any relevant symptoms, it is crucial to act swiftly by following the instructions provided in the recall notification or reaching out to your local dealership.

Brake Pressure Switch Short May Cause Fire In Chevy Trucks

Posted on by

General Motors. LLC (GM) has decided that a problem exists in certain 2019-2023 Chevrolet 4500HD, 5500HD, and 6500HD medium-duty trucks. The brake pressure sensor assembly could leak brake fluid into the brake pressure switch and cause an electrical short circuit.

GM opened an investigation in August 2022 following reports of a vehicle fire on a 2019 Chevrolet Silverado medium-duty truck. As part of that investigation, GM reviewed field data potentially related to the problem and warranty returned brake pressure sensors.

While a series of tests failed to duplicate the condition, in January, a warranty-returned sensor and harness were identified as exhibiting signs of heat damage. This part was subjected to more detailed analysis, including X-ray scans and a chemistry laboratory analysis. The results from these analyses revealed the presence of brake fluid past the diaphragm seal, into the brake pressure switch, and through the actual wire harness into the pump’s fuse circuit. An inspection of the returned components also revealed delamination of the corrosion-inhibiting sealant, which allowed slow seepage of the brake fluid past the diaphragm seal.

According to the defect report, a zinc-nickel plating and sealant used to inhibit corrosion within the pressure sensor assembly may cause delamination of the sealant which results in small fragments of sealer underneath the diaphragm during assembly which allows brake fluid to slowly seep past the seal and into the pressure switch. The brake fluid may seep into the sensor’s electrical components and short the brake pressure switch and the associated fuse. If brake fluid shorts the brake pressure switch and the fuse, the circuit can generate enough heat and could result in a fire. An under-hood fire may occur when the vehicle is off and possibly unattended.

Owners are advised to park outside and away from structures until the recall repair is complete. Dealers will replace the master cylinder pressure sensor and inspect the wire harness. If the harness is damaged, it will be replaced as well. Interim letters notifying owners of the safety risk are expected to be mailed on May 29, 2023. Second letters will be mailed once the remedy is available. GM’s number for this recall is N222375270 and the NHTSA campaign number is 23V-266.

Ram 1500 Engine Stall Due To PCM Issue

Posted on by

Chrysler (FCA) has recently made an announcement to the public regarding the recall of certain 2021 Ram 1500 vehicles. The reason behind the recall is an unexpected engine stall issue that has been identified in some of the vehicles equipped with 5.7L eTorque engines. An engine stall can cause an increased risk of an accident, which can be life-threatening.

FCA’s Technical Safety and Regulatory Compliance (TSRC) organization initiated an investigation into the matter in January 2023, after receiving several reports regarding the potential stall condition in a 2021 Ram 1500 equipped with the 5.7LeTorque engine. The investigation revealed that the Powertrain Control Module (PCM) software was the root cause of the stall pattern in the affected vehicles.

The vehicles that were manufactured between June 3, 2020, and September 12, 2021, have been identified to have defective powertrain control module software, which can cause an incorrect fuel mixture condition in the engine and eventually result in an engine stall.

Chrysler is notifying owners to bring their vehicles in for repair. According to the defect report, the company has identified 206 customer records, 636 warranty claims, and 53 field reports related to this issue. This recall is expected to affect a significant number of vehicles, and Chrysler is urging all affected vehicle owners to take immediate action to prevent any potential accidents or harm.

If you are an owner of one of the affected vehicles, you are entitled to a free repair. Under the Lemon Law, manufacturers are required to replace or refund the purchase price of a vehicle that has a recurring defect that cannot be repaired within a reasonable number of attempts. If your vehicle is affected and the repair is not successful, you may be eligible for a refund or replacement under this law.

The affected vehicles will be repaired by updating the Powertrain Control Module calibration software. The recall number for this specific recall is 37A, and the NHTSA campaign number is 23V-265. It is important to act immediately if you are an owner of one of these vehicles to avoid any potential safety risks.

Chevy Express & GMC Savana HVAC Circuit May Overheat

Posted on by

General Motors (GM) is one of the largest automobile manufacturers in the world, with a reputation for producing reliable and safe vehicles. However, like all automakers, GM occasionally identifies issues with its vehicles that need to be addressed to ensure the safety of its customers. Recently, GM identified a problem in certain 2003-2023 Chevrolet Express Cutaway and 2003-2023 GMC Savana Cutaway incomplete vehicles. These vehicles are equipped with wiring for an optional rear heating, ventilation, and air-conditioning (HVAC) system.

According to the defect report, these vehicles are equipped with an unused circuit that a final-stage manufacturer may elect to use to install an optional rear HVAC system. While this circuit is not typically used, if the final-stage manufacturer leaves the circuit’s connectors or cut wires unsealed, where exposure to moisture or contamination may, over time, cause corrosion. In rare cases, this corrosion could result in a high current draw through the circuit at the vehicles’ lower left side B-pillar. If left unaddressed, the problem could cause excessive heat in the circuit that could result in a fire.

To address this problem, GM began a product investigation in December 2022, after receiving reports of two alleged fire incidents involving a 2013 and a 2014 Chevrolet Express Cutaway incomplete vehicles. The company’s investigators analyzed inspection reports from the two subject vehicles and retrieved and analyzed field data for all Express Cutaway and GMC Savana Cutaway vehicles sold for model years 2005 through 2023, comprising approximately 167,000 units. Analysis of the field data, including legal claims, identified a total of eight potentially related complaints, six of which alleged fires.

On March 30, 2023, GM’s Safety Field Action Decision Authority (SFADA) decided to conduct a safety recall. While the company is not aware of any accidents or injuries associated with this condition, it is taking this action to ensure the safety of its customers.

Owners of the affected vehicles will receive notices with instructions to return to their dealers to have the rear HVAC blower motor circuits at the left side B-pillar properly sealed. The recall is identified by GMC’s number N222386050 and the NHTSA campaign number is 23V-247.

Electrical Short In Battery Of Kia Soul EVs

Posted on by

Kia will be contacting owners of certain 2015-2019 Kia Soul EVs about a problem that could result in a short circuit in the high voltage battery pack and a potential vehicle fire.

Kia first became aware of the problem in May 2022 when they received reports of smoke from the battery vents located under the passenger seat on a 2017 Kia Soul EV. Kia records showed that the vehicle’s high-voltage battery had been previously replaced under warranty. In October Kia received a second report, involving a 2018 Soul EV. The customer reported the smell of smoke just before the vehicle stalled. Kia performed CT scans and a tear-down analysis for both vehicles but the results were inconclusive due to thermal damage and water intrusion from fire suppression.

As Kia investigated the first two reports they received a third customer complaint of popping noises and smoke coming from the cup holders of a 2018 Soul EV in Hawaii. Kia and the battery supplier inspect vehicle #3 and performed a tear down analysis which found the heat damage was limited to the battery case assembly. The preliminary investigation results were inconclusive and the battery was shipped to the manufacturer for further analysis.

According to the defect report, an electrical short between the anode and cathode of the battery cells can occur with the high-voltage battery pack assembly case. The cause of the electrical short circuit is unknown but believed to be caused by abnormally excessive precipitate within the battery cells.

Although the cause of the electrical short circuit is unknown, Kia has decided to recall all 2018-2019MY Soul EV vehicles equipped with an E400 battery and certain 2015-2017MY Soul EV vehicles that had the high voltage battery replaced under warranty with E400 battery.

Dealers will update the battery management system software with new software that will illuminate the EV warning light, limit charging capacity, and reduce vehicle power if an abnormal voltage is detected. If this occurs, the battery will be replaced. Owner notification letters are expected to be mailed on May 26, 2023. Kia’s number for this recall is SC267 and the NHTSA campaign number is 23V-218.

There have been three (3) thermal incidents limited to the battery case assembly with no injuries, no crashes, and no fatalities.

2023 Genesis G90 Abnormal Pretensioner Deployment

Posted on by

Hyundai Motor America (Hyundai) will be contacting the owners of certain 2023 Genesis G90 luxury sedans because of a defect affecting the seat belt pretensioners in their vehicles. The problem could result in an increased chance of injury to vehicle occupants.

In October 2022, Hyundai received information pertaining to an investigation into allegations of abnormal seat belt pretensioner deployments in vehicles associated with recalls 21V-796, 22V-069, 22V-123, 22V-218, 22V-354, and 22V-458. Recall 22V-816 was initiated as Hyundai continued to evaluate vehicles equipped with the same Samsong pretensioners that had not yet been recalled..

In January, during the continued analysis of the airbag control unit (ACU) crash pulse data recovered from a North Carolina incident, they found that the micro gas generator (MGG) separated despite having a lower pretensioner “time-to-fire”. This was the problem that was previously thought to be the contributor to over-pressurization of the pretensioner pipe. Because of this information, the North America Safety Office (NASO) decided to conduct a safety recall 012G (23V-094) of Genesis G80, GV60, GV70, and GV80 vehicles equipped with pretensioners without a vent valve. Recall 012G (23V-094) supersedes Recall 009G, obsoleting all affected population(s) of Recall 211/009G (21V-796).

In March, during the review of details surrounding Hyundai’s assessment of the open investigation into the recent recalls, Hyundai noted that the recent recalls address all U.S. vehicles equipped with the subject Samsong seat belt pretensioner excluding Genesis G90 vehicles. The G90 contains the same seat belt pretensioners but because it is installed facing outward and away from occupants, fragments entering the cabin area and injuring occupants are significantly less likely to happen. Based on this information, the NASO decided to conduct a safety recall (013G) of Genesis G90 vehicles equipped with pretensioners without a vent valve. NHTSA campaign number 23V-210.

According to the defect report, the subject vehicles are equipped with frontal/rear pyrotechnic-type seat belt pretensioners that could deploy abnormally in certain crash conditions. The problem is due to the over-pressurization of the pretensioner pipe. Depending on specific vehicle characteristics such as pretensioner load limiter specification, the airbag control unit logic, crash duration/severity, and micro-gas generator orientation, occupants could experience an increased risk of injury.

Owners of the affected vehicles will be notified with instructions to bring their vehicles to a Hyundai dealer to have the seat belt pretensioner’s micro gas generator and delivery pipe secured with a cap to prevent potential abnormal deployment.

Volvo Emergency Call False Warning Message

Posted on by

Volvo Car USA, the American arm of the Swedish automaker, has announced that it will be contacting owners of certain 2023 Volvo vehicles regarding a problem that could lead to the failure of the e-call system, a crucial safety feature in modern cars.

Volvo first became aware of the problem in March 2023, when a customer reported a false warning message being displayed on the Driver Information Module (DIM). Upon investigation, it was discovered that the problem was related to the Telematics and Connectivity Antenna Module (TCAM), which could mis-detect a communication failure with the Infotainment Head Unit (IHU) during a software download.

The issue was escalated to the Critical Concern Action Process (CCAP) and subsequently to the Critical Concern Management Team (CCMT) for further review. After a thorough analysis of the data, the decision was made to issue a recall for the affected vehicles.

2023 Volvo C40
2023 Volvo S60
2023 Volvo V60CC
2023 Volvo XC40
2023 Volvo XC60
2023 Volvo XC90

Although there will be no actual loss of expected functions, the falsely set Diagnostic Trouble Codes (DTC) could lead to confusion in case of an actual emergency, increasing the risk of no emergency response. Therefore, it is imperative that owners of affected vehicles take this recall seriously and get their vehicles updated as soon as possible.

The recall has been assigned the Volvo Car’s number R10225, and the NHTSA campaign number is 23V-188. It is worth noting that such recalls are not uncommon in the automotive industry. Car manufacturers routinely monitor their vehicles for issues, to ensure that their vehicles remain safe.

In conclusion, Volvo Car USA will be updating the software in certain 2023 Volvo vehicles to address the e-call system issue. The recall is a precautionary measure to ensure the safety of its customers. It is recommended that owners of the affected vehicles take the recall seriously and bring their vehicles in for the necessary software update as soon as possible.